The size of a bobbin must match precisely with the machine’s bobbin area. Just because a bobbin seems to be a similar size, the slightest difference can wreck havoc for its owner. A sewing machines bobbin case tension is properly set based on the machine’s correct bobbin type.
Do all sewing machines use the same bobbins?
There is no such thing as a universal bobbin, meaning no single bobbin will fit every sewing machine. Some sewing machines tolerate a slightly different bobbin better than others, but using the incorrect bobbin will most likely affect the stitch quality of your project, and could result in damage to your machine.
What happens if I use the wrong bobbin?
The short answer is YES! Filling a sewing machine bobbin too tightly can make a plastic bobbin bulge or stretch the thread if you are using a metal bobbin. This may be hard to see but can cause all kinds of problems. Plastic bobbins can become compressed in the center causing the bobbin to distort.
Are bobbin cases interchangeable?
While they are technically interchangeable in most cases, it is recommended that you only use one or the other. The weight of the bobbin can affect your tension and the way the thread feeds. These are the most common bobbins, as they are used with removable and inset bobbin cases.
Are metal or plastic bobbins better?
The rule of thumb for bobbins is that metal ones are for metal bobbin cases and plastic ones are for plastic bobbin cases. If you try to place a metal bobbin in a plastic bobbin case you may see that the bobbin case wears out a lot faster than it is supposed to.
Can I use metal bobbins in My Brother sewing machine?
Plastic bobbins and metal bobbins of the same size can NOT be swapped. Machines are set for a very precise tension setting. If they are set for a lighter plastic bobbin, the tension will change if a heavier metal bobbin is used.
Does the size of the bobbin matter?
Bobbins not only come in different sizes, but also in metal as well as plastic, and empty as well as pre-wound. While machines can only use one bobbin size, whether it is plastic or metal does not typically matter, however consult your machine manual to be sure.
What is the difference between a 15 and a 15J bobbin?
They look almost identical, but class 15 bobbins have flat ends, while class 15J bobbins have slightly curved ends. Sometimes they appear to work interchangeably, but even if they fit into your sewing machine, there is a risk of them jamming your machine up and causing major damage.
What size is a Class 15 bobbin?
The Class 15 (A Style) Bobbin:
The Class 15 is about the size of an American nickel. Its diameter measures approximately 20.3 mm and has a width of approximately 11.7 mm.
What are the holes in bobbins for?
Then take a look at your bobbin. There should be a tiny little hole on the side for you to put your thread through. Thread from the inside of the bobbin, out, so your thread sticks out the side an inch or two.
Can you use a sewing machine without a bobbin?
Can you use a sewing machine without a bobbin? You can’t sew without a bobbin, as the machine requires two spools in order to operate properly. Therefore, you will need to add the bobbin thread in addition to your needle thread.
Does bobbin thread need to match?
You will always want to use a lightweight polyester bobbin thread, such as BobbinFil or any other 60-70 weight thread. You can use whatever color you want, but you don’t need to change color to match the top thread. Your bobbin thread should not show through the top layer of stitching.
How do you know if you need a new bobbin case?
A quarter of a turn is a lot. Again, you only need to worry about the bobbin tension if the factory set bobbin tension isn’t creating a balanced stitch. As long as you take good care of your bobbin case, it will perform well. However, eventually, it will cease to sew smoothly and will need to be replaced.
What are the different bobbin sizes?
- Size 207 – 0.020″ (0.51 mm) – 70 Yards.
- Size 415 – 0.030″ (0.76 mm) – 70 Yards.
- Size 450 – 0.035″ (0.89 mm) – 70 Yards.
- Size 475 – 0.040″ (1.02 mm) – 70 Yards.
- Size 500 – 0.045″ (1.14 mm) – 70 Yards.
- Size 554 – 0.050″ (1.27 mm) – 70 Yards.
- Size 277 – 0.025″ (0.64 mm) – 24 Yards.
- Size 415 – 0.030″ (0.76 mm) – 12 Yards.